Electromagnetic interference

Integrated circuits are often a source of EMI, but they are never the "antenna". They must couple their energy to larger objects such as heatsinks, circuit board planes and cables to radiate significantly .
On integrated circuits, important means of reducing EMI are: the use of bypass or "decoupling" capacitors on each active device (connected across the power supply, as close to the device as possible), rise time control of high-speed signals using series resistors, and VCC filtering. Shielding is usually a last resort after other techniques have failed because of the added expense of RF gaskets and the like.
The efficiency of the radiation depends on the height above the ground or power plane (at RF one is as good as the other) and the length of the conductor in relation to the wavelength of the signal component (fundamental, harmonic or transient (overshoot, undershoot or ringing)). At lower frequencies, such as 133 MHz, radiation is almost exclusively via I/O cables; RF noise gets onto the power planes and is coupled to the line drivers via the VCC and ground pins. The RF is then coupled to the cable through the line driver as common-mode noise. Since the noise is common-mode, shielding has very little effect, even with differential pairs. The RF energy is capacitively coupled from the signal pair to the shield and the shield itself does the radiating. One cure for this is to use a braid-breaker or choke to reduce the common-mode signal.
At higher frequencies, usually above 500 MHz, traces get electrically longer and higher above the plane. Two techniques are used at these frequencies: wave shaping with series resistors and embedding the traces between the two planes. If all these measures still leave too much EMI, shielding such as RF gaskets and copper tape can be used. Most digital equipment is designed with metal, or conductive-coated plastic, cases.

Susceptibilities of different radio technologies
Interference tends to be more troublesome with older radio technologies such as analogue amplitude modulation, which have no way of distinguishing unwanted in-band signals from the intended signal, and the omnidirectional dipole antennas used with broadcast systems. Newer radio systems incorporate several improvements that improve the selectivity. In digital radio systems, such as Wi-Fi, error-correction techniques can be used. Spread-spectrum and frequency-hopping techniques can be used with both analogue and digital signalling to improve resistance to interference. A highly directional receiver, such as a parabolic antenna or a diversity receiver, can be used to select one signal in space to the exclusion of others.
The most extreme example of digital spread-spectrum signalling to date is ultra-wideband (UWB), which proposes the use of large sections of the radio spectrum at low amplitudes to transmit high-bandwidth digital data. UWB, if used exclusively, would enable very efficient use of the spectrum, but users of non-UWB technology are not yet prepared to share the spectrum with the new system because of the interference it would cause to their receivers. The regulatory implications of UWB are discussed in the Ultra-wideband article.

Interference to consumer devices
Complex electronic circuitry is found in all sorts of devices used in the home. This results in a vast interference potential that didn't exist in earlier, simpler decades. In the US, Public Law 97-259, enacted in 1982, gave the FCC the authority to regulate the susceptibility of consumer electronic equipment sold in the United States. The FCC, working with equipment manufacturers, decided to allow them to develop standards for EMI immunity and implement their own voluntary compliance programs.
Broadcast transmitters, two-way radio transmitters, paging transmitters, and cable TV are potential sources of RFI and EMI.Other possible sources of interference include a wide variety of devices, such as doorbell transformers, toaster ovens, electric blankets, ultrasonic pest control devices, electric bug zappers, heating pads, and touch controlled lamps. Multiple CRT computer monitors or televisions sitting too close to one another can sometimes cause a "shimmy" effect in each another, due to the electromagnetic nature of their picture tubes, especially when one of their de-gaussing coils is activated.
Switching inductive loads, such as electric motors, off causes interference, but it is easily suppressed by connecting a snubber network, a resistor in series with a capacitor, across the switch. Exact values can be optimised for each case, but 100 ohms in series with 100 nanofarads is usually satisfactory.
Switched-mode power supply can be a source of EMI, but have become less of a problem as design techniques have improved, such as integrated power factor correction.
Most countries have legal requirements that mandates electromagnetic compatibility: electronic and electrical hardware must still work correctly when subjected to certain amounts of EMI, and should not emit EMI which could interfere with other equipment (such as radios).

Bamboo Table Set

mirror wall tile

Ride On Motorbike

Socket Tool Set

embroidered denim jeans

Plastic Ball Valve

foam folding chair

decorative glass bottle

blister packaging machinery

vinyl acetate monomer

Impact Screw Driver

Bicycle Spare Parts

AA Battery Case

iron stepping stone

cotton tote bags

Portable Car Lifts

european leather sofa

electric soldering iron

VoIP USB Handset

Heavy Duty Webbing

solenoid valve coil

key selector switch

Floating Ball Light

Yarn Dyed Shirt

USB DVB Stick

bathroom wall panel

metal engraving machine

electric heating pad

Black CRT Monitor

acrylic paper weight